The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and Split Taper Bushing china pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For work with with 5/8” shaft sizes. Comes with set screws. Additional Features: Made of Steel For make use of with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering on hand requirements and enabling adjustments in shaft size if necessary. The barrel of the split tapered bushing is definitely split in two areas and is definitely keyed to the shaft. The barrel OD is also keyed to the drive component as well. The benefit of the split tapered bushing could it be will hold, even if the fasteners turn into loose. Split tapered bushings happen to be interchangeable between manufacturers.
Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered elements with wonderful tolerance. The characteristic is easy to make use of and needs no extra alteration. These bushings can match almost all varieties of assemblies and sizes. They are the best 
choice in design for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: complete range of both metric and imperial readily available.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends on the application.
Complete brief reach range offered, for compact light assemblies & Clean, Compact Style.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for durability and strength. U1 bushings are used in an extensively broad range of applications, including; sprockets, shaves, pulleys, gears, plus much more, we likewise offer all of these goods. What sets this bushing apart is the high-quality steel engineering along with precise manufacturing and top quality control; this means that you always get yourself a premium quality constant product. What really models us in addition to the other folks is our highly trained expert staff members and our company-wide target of customer satisfaction.
1. Be sure the tapered cone floors of the bushing and the within of the driven product happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or additional portion type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to assure sliding match on shaft.
4. With major on shaft, slide the sprocket or other part type to the required situation on the shaft. Be sure to keep the heads of the cap screws available.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they are pulled up tight. Usually do not apply extensions on the wrench handles and do not permit the sprocket or part to always be drawn i contact with flange of bushing. At this point there must be a gap between the bushing flange and sprocket, make certain this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key on most sizes for great drive and higher torque carrying capabilities
Double-split barrel for great clamping
Solid flange to keep concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys upon both shaft and merchandise to supply the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest degree of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you need. For make use of with 5/8” shaft sizes. Comes with set screws. Further Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering on hand requirements and allowing for adjustments in shaft size if important. The barrel of the split tapered bushing is normally split in two locations and can be keyed to the shaft. The barrel OD can be keyed to the drive component aswell. The benefit of the split tapered bushing could it be will hold, even if the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.